+=== 1^SHOW/ISOLATE^Show list of ISOLATED nodes
+
+=== 9^SHOW/LOCKOUT^Show the list of locked out or excluded callsigns
+
+=== 0^SHOW/MOON [<prefix>|<callsign>]^Show Moon rise and set times
+Show the Moon rise and set times for a (list of) prefixes or callsigns,
+together with the azimuth and elevation of the sun currently at those
+locations.
+
+If you don't specify any prefixes or callsigns, it will show the times for
+your QTH (assuming you have set it with either SET/LOCATION or SET/QRA),
+together with the current azimuth and elevation.
+
+In addition, it will show the gain or loss dB relative to the nominal
+distance of 385,000Km due to the ellipsoidal nature of the orbit.
+
+If all else fails it will show the Moonrise and set times for the node
+that you are connected to.
+
+For example:-
+
+ SH/MOON
+ SH/MOON G1TLH W5UN
+
+=== 0^SHOW/MUF <prefix> [<hours>][long]^Show the likely propagation to a prefix
+This command allow you to estimate the likelihood of you contacting
+a station with the prefix you have specified. The output assumes a modest
+power of 20dBW and receiver sensitivity of -123dBm (about 0.15muV/10dB SINAD)
+
+The result predicts the most likely operating frequencies and signal
+levels for high frequency (shortwave) radio propagation paths on
+specified days of the year and hours of the day. It is most useful for
+paths between 250 km and 6000 km, but can be used with reduced accuracy
+for paths shorter or longer than this.
+
+The command uses a routine MINIMUF 3.5 developed by the U.S. Navy and
+used to predict the MUF given the predicted flux, day of the year,
+hour of the day and geographic coordinates of the transmitter and
+receiver. This routine is reasonably accurate for the purposes here,
+with a claimed RMS error of 3.8 MHz, but much smaller and less complex
+than the programs used by major shortwave broadcasting organizations,
+such as the Voice of America.
+
+The command will display some header information detailing its
+assumptions, together with the locations, latitude and longitudes and
+bearings. It will then show UTC (UT), local time at the other end
+(LT), calculate the MUFs, Sun zenith angle at the midpoint of the path
+(Zen) and the likely signal strengths. Then for each frequency for which
+the system thinks there is a likelihood of a circuit it prints a value.
+
+The value is currently a likely S meter reading based on the conventional
+6dB / S point scale. If the value has a '+' appended it means that it is
+1/2 an S point stronger. If the value is preceeded by an 'm' it means that
+there is likely to be much fading and by an 's' that the signal is likely
+to be noisy.
+
+By default SHOW/MUF will show the next two hours worth of data. You
+can specify anything up to 24 hours worth of data by appending the no of
+hours required after the prefix. For example:-
+
+ SH/MUF W
+
+produces:
+
+ RxSens: -123 dBM SFI: 159 R: 193 Month: 10 Day: 21
+ Power : 20 dBW Distance: 6283 km Delay: 22.4 ms
+ Location Lat / Long Azim
+ East Dereham, Norfolk 52 41 N 0 57 E 47
+ United-States-W 43 0 N 87 54 W 299
+ UT LT MUF Zen 1.8 3.5 7.0 10.1 14.0 18.1 21.0 24.9 28.0 50.0
+ 18 23 11.5 -35 mS0+ mS2 S3
+ 19 0 11.2 -41 mS0+ mS2 S3
+
+indicating that you will have weak, fading circuits on top band and
+80m but usable signals on 40m (about S3).
+
+inputing:-
+
+ SH/MUF W 24
+
+will get you the above display, but with the next 24 hours worth of
+propagation data.
+
+ SH/MUF W L 24
+ SH/MUF W 24 Long
+
+Gives you an estimate of the long path propagation characterics. It
+should be noted that the figures will probably not be very useful, nor
+terrible accurate, but it is included for completeness.
+
+=== 1^SHOW/NODE [<callsign> ...]^Show the type and version number of nodes
+Show the type and version (if connected) of the nodes specified on the
+command line. If no callsigns are specified then a sorted list of all
+the non-user callsigns known to the system will be displayed.
+