-<P>There are two main types of filter, <EM>accept</EM> or <EM>reject</EM>. You
-can use either to achieve the result you want dependent on your own preference
-and which is more simple to do. It is pointless writing 8 lines of reject
-filters when 1 accept filter would do the same thing! Each filter has 10
-lines (of any length) which are tried in order. If a line matches then the
-action you have specified is taken (ie reject means ignore it and accept
-means take it)
-<P>
-<P>If you specify reject filters, then any lines that arrive that match the filter
-will be dumped but all else will be accepted. If you use an accept filter,
-then ONLY the lines in the filter will be accepted and all else will be dumped.
-For example if you have a single line <EM>accept</EM> filter ...
-<P>
-<BLOCKQUOTE><CODE>
-<PRE>
-accept/spots on vhf and (by_zone 14,15,16 or call_zone 14,15,16)
-</PRE>
-</CODE></BLOCKQUOTE>
-<P>then you will <EM>ONLY</EM> get VHF spots <EM>from</EM> or <EM>to</EM> CQ zones
-14, 15 and 16.
-<P>
-<P>If you set a reject filter like this ...
-<P>
-<BLOCKQUOTE><CODE>
-<PRE>
-reject/spots on hf/cw
-</PRE>
-</CODE></BLOCKQUOTE>
-<P>Then you will get everything <EM>EXCEPT</EM> HF CW spots. You could make this
-single filter even more flexible. For example, if you are interested in IOTA
-and will work it even on CW even though normally you are not interested in
-CW, then you could say ...
-<P>
-<BLOCKQUOTE><CODE>
-<PRE>
-reject/spots on hf/cw and not info iota
-</PRE>
-</CODE></BLOCKQUOTE>
-<P>But in that case you might only be interested in iota and say:-
-<P>
-<BLOCKQUOTE><CODE>
-<PRE>
-accept/spots not on hf/cw or info iota
-</PRE>
-</CODE></BLOCKQUOTE>
-<P>which achieves exactly the same thing. You should choose one or the other
-until you are comfortable with the way it works. You can mix them if you
-wish (actually you can have an accept AND a reject on the same line) but
-don't attempt this until you are sure you know what you are doing!
-<P>
-<P>You can arrange your filter lines into logical units, either for your own
-understanding or simply convenience. Here is an example ...
-<P>
-<BLOCKQUOTE><CODE>
-<PRE>
-reject/spots 1 on hf/cw
-reject/spots 2 on 50000/1400000 not (by_zone 14,15,16 or call_zone 14,15,16)
-</PRE>
-</CODE></BLOCKQUOTE>
-<P>What this does is to ignore all HF CW spots and also rejects any spots on VHF
-which don't either originate or spot someone in Europe.
-<P>
-<P>This is an example where you would use a line number (1 and 2 in this case), if
-you leave the digit out, the system assumes '1'. Digits '0'-'9' are available.
-This make it easier to see just what filters you have set. It also makes it
-more simple to remove individual filters, during a contest for example.
-<P>
-<P>You will notice in the above example that the second line has brackets. Look
-at the line logically. You can see there are 2 separate sections to it. We
-are saying reject spots that are VHF or above <EM>APART</EM> from those in
-zones 14, 15 and 16 (either spotted there or originated there). If you did
-not have the brackets to separate the 2 sections, then Spider would read it
-logically from the front and see a different expression entirely ...
-<P>
-<BLOCKQUOTE><CODE>
-<PRE>
-(on 50000/1400000 and by_zone 14,15,16) or call_zone 14,15,16
-</PRE>
-</CODE></BLOCKQUOTE>
-<P>The simple way to remember this is, if you use OR - use brackets. Whilst we are
-here CASE is not important. 'And BY_Zone' is just the same as 'and by_zone'.
-<P>As mentioned earlier, setting several filters can be more flexible than
-simply setting one complex one. Doing it in this way means that if you want
-to alter your filter you can just redefine or remove one or more lines of it or
-one line. For example ...
+<P>Bulletin mail is sent by using the <EM>sb</EM> command. This is one of the
+most common mistakes users make when sending mail. They send a bulletin
+mail with <EM>s</EM> or <EM>sp</EM> instead of <EM>sb</EM> and of course
+the message never leaves the cluster. This can be rectified by the sysop
+by using the <EM>msg</EM> command.</P>
+
+<P>Bulletin addresses can be set using the Forward.pl file.</P>
+
+<H2><A NAME="ss3.3">3.3</A> <A HREF="adminmanual.html#toc3.3">Forward.pl</A>
+</H2>
+
+<P>DXSpider receives all and any mail sent to it without any alterations needed
+in files. Because personal and bulletin mail are treated differently, there
+is no need for a list of accepted bulletin addresses. It is necessary, however,
+to tell the program which links accept which bulletins. For example, it is
+pointless sending bulletins addresses to "UK" to any links other than UK
+ones. The file that does this is called forward.pl and lives in /spider/msg.
+At default, like other spider files it is named forward.pl.issue. Rename it
+to forward.pl and edit the file to match your requirements.
+The format is below ...</P>