fixed set/obscount

[spider.git] / cmd / Commands_en.hlp

diff --git a/cmd/Commands_en.hlp b/cmd/Commands_en.hlp
index 257e171397316a94bb95cf4a895f61d9393ac678..1cd2b30f664ff0087f2b66b97b19cecd01400ee3 100644 (file)
--- a/cmd/Commands_en.hlp
+++ b/cmd/Commands_en.hlp
@@ -695,11 +695,6 @@ etc). eg:-
 or 
    pc G1TLH Try doing that properly!!!
 
-=== 1^PING <node>^Send a ping command to another cluster
-This command is used to estimate the quality of the link to another cluster. 
-The time returned is the length of time taken for a PC51 to go to another 
-cluster and be returned.
-
 === 0^KILL <msgno> [<msgno> ...]^Remove or erase a message from the system
 You can get rid of any message to or originating from your callsign using 
 this command. You can remove more than one message at a time.
@@ -720,10 +715,11 @@ PC protocol to connected nodes either for testing or to unstick things.
 You can also use in the same way as a talk command to a connected user but
 without any processing, added of "from <blah> to <blah" or whatever.
  
-=== 1^PING <node call>^Find out the delays an a circuit to another node
-This command will enable sysops to determine the speed of an inter-cluster
-node. 
-
+=== 1^PING <node call>^Check the link quality between nodes
+This command allows you to send a frame to another cluster node on
+the network and get a return frame.  The time it takes to do this
+is a good indication of the quality of the link.  The actual time
+it takes is output to the console in seconds.
 Any visible cluster node can be PINGed.
 
 === 1^RCMD <node call> <cmd>^Send a command to another DX Cluster
@@ -1057,6 +1053,10 @@ If a ping is heard then the obscount is reset to the full value. Using
 default values, if a node has not responded to a ping within 15 minutes,
 it is disconnected.
 
+You can set this parameter between 1 and 9.
+
+It is STRONGLY recommended that you don't change the default.
+
 === 0^SET/PAGE <lines per page>^Set the lines per page
 Tell the system how many lines you wish on a page when the number of line
 of output from a command is more than this. The default is 20. Setting it
@@ -1073,13 +1073,29 @@ affect routing decisions. The default interval is 300 secs or 5 minutes.
 
 You can use this command to set a different interval. Please don't. 
 
-But if you do the value you enter is treated as minutes up 60 and seconds
+But if you do the value you enter is treated as minutes up 30 and seconds
 for numbers greater than that.
 
 This is used also to help determine when a link is down at the far end
 (as certain cluster software doesn't always notice), see SET/OBSCOUNT
 for more information.
 
+If you must change it (and it may be useful for internet connected nodes
+on dynamic IP addresses that go away after a set time of usage) the time
+can be specified as:-
+
+  5      which if less than 30 is converted to minutes otherwise is 
+         taken as the no of seconds between pings. 
+  120s   120 seconds
+  5m     5 minutes
+  1h     1 hour
+
+Please be aware that this causes traffic to occur on the link, setting 
+this value too low may annoy your neighbours beyond the point of 
+endurance!
+
+You can switch this off by setting it to 0.
+
 === 9^SET/PRIVILEGE <n> <call> [<call..]^Set privilege level on a call
 Set the privilege level on a callsign. The privilege levels that pertain
 to commands are as default:-
@@ -1352,8 +1368,8 @@ and returns any information available for that callsign. This service
 is provided for users of this software by http://www.qrz.com 
 
 === 0^SHOW/ROUTE <callsign> ...^Show the route to the callsign
-This command allows you to see which node the callsigns specified are
-connected via. It is a sort of inverse sh/config.
+This command allows you to see to which node the callsigns specified are
+connected. It is a sort of inverse sh/config.
 
 sh/route n2tly