message.
You can carry on with the message until you are ready to send it.
+
+=== 6^SEND_CONFIG^Broadcast PC92 C records
+This is the PC92 equivalent of INIT. In that it will send out a new
+PC92 C record to all interfaces. This can be used to bring other nodes
+up to date quicker after a restart.
+
=== 0^SET/ADDRESS <your address>^Record your postal address
=== 9^SET/AGWENGINE^Enable the AGW Engine
=== 9^SET/LOCKOUT <call>^Stop a callsign connecting to the cluster
=== 9^UNSET/LOCKOUT <call>^Allow a callsign to connect to the cluster
+=== 8^SET/MAXCONNECT <value> [<call> ..]^Set max incoming connections for user/node
+Set the maximum no of connections (parents) an incoming user or node is
+allowed to have. If this incoming connection takes it over the separate
+limits for users and nodes (defaults: 3 and 8 respectively), then the
+connection is refused (with a polite message).
+
+The idea behind this to limit the number of copies of messages that
+are sent to users (and nodes). Nodes really don't need to have more than
+5 or 6 partners and users don't need more than two connections into the
+cluster cloud.
+
+This check is only for INCOMING connections, no check is performed for
+outgoing connections.
+
=== 0^SET/NAME <your name>^Set your name
Tell the system what your name is eg:-
SET/NAME Dirk
This command shows the hop counts set up for a node. You can specify
which category you want to see. If you leave the category out then
all the categories will be listed.
-
+
+=== 0^SHOW/IK3QAR <callsign>^Obtain QSL info from IK3QAR database
+Get QSL information from the online dabase run by IK3QAR.
+
+Your sysop needs to set up this command by obtaining a password from IK3QAR.
+Instructions are available in local/Internet.pm
+
=== 1^SHOW/ISOLATE^Show list of ISOLATED nodes
=== 9^SHOW/LOCKOUT <prefix>|ALL^Show the list of locked out or excluded callsigns
Please note that the rise and set times are given as the UT times of rise and
set on the requested UT day.
+=== 0^SHOW/MOTD^Show your MOTD (the Message of the Day)
+The Message of the Day is normally printed whenever one logs on. However
+many people now login using logging programs or something other than plain
+telnet or ax25 connections. This command allows the user (or the program)
+to see what is in the MOTD.
+
+The actual MOTD that you are shown depends on what carrier you are logged
+on via, whether you are registered and some other factors that your sysop
+may have thrown in.
+
=== 0^SHOW/MUF <prefix> [<hours>][long]^Show the likely propagation to a prefix
This command allow you to estimate the likelihood of you contacting
a station with the prefix you have specified. The output assumes a modest
Doing a SHOW/MYDX will now only, ever, show HF spots. All the other
options on SH/DX can still be used.
-=== 0^SHOW/NEWCONFIGURATION [<node>]^Show all the nodes and users visible
-This command allows you to see all the users that can be seen
-and the nodes to which they are connected.
+=== 0^SHOW/NEWCONFIGURATION [USERS|<node call>]^Show the cluster map
+Show the map of the whole cluster.
-This command produces essentially the same information as
-SHOW/CONFIGURATION except that it shows all the duplication of
-any routes that might be present It also uses a different format
-which may not take up quite as much space if you don't have any
-loops.
+This shows the structure of the cluster that you are connected to. By
+default it will only show the nodes that are known. By adding the keyword
+USER to the command it will show all the users as well.
-BE WARNED: the list that is returned can be VERY long
+As there will be loops, you will see '...', this means that the information
+is as printed earlier and that is a looped connection from here on.
+
+BE WARNED: the list that is returned can be VERY long (particularly
+with the USER keyword)
=== 0^SHOW/NEWCONFIGURATION/NODE^Show all the nodes connected locally
Show all the nodes connected to this node in the new format.
projects / spider.git / blobdiff