is that of the "sysop" user [which had BETTER NOT BE "root"]), you will
need to create any directories you want to put stuff in beforehand as well.
+It is likely that you will want to run these commands in a crontab type
+situation. You would do that something like:-
+
+ 0 0 * * * run_cmd('save /tmp/dxstats echo "DXStat Table", "sh/dxstats"')
+
+Note that you still enclose each command with (") characters but you must
+enclose the entire save command in (') characters.
+
+Now in fact, this can be varied if you know what you are doing. See the
+admin manual for more details.
+
=== 0^SEND <call> [<call> ...]^Send a message to one or more callsigns
=== 0^SEND RR <call>^Send a message and ask for a read receipt
=== 0^SEND COPY <msgno> <call>^Send a copy of a message to someone
SEND <call> on its own acts as though you had typed SEND PRIVATE, that is
it will mark the message as personal and send it to the cluster node that
-that callsign is connected to.
+that callsign is connected to. If the <call> you have specified is in fact
+a known bulletin category on your node (eg: ALL) then the message should
+automatically become a bulletin.
You can have more than one callsign in all of the SEND commands.
SB is an alias for SEND NOPRIVATE (or send a bulletin in BBS speak)
SP is an alias for SEND PRIVATE
+The system will ask you for a subject. Conventionally this should be
+no longer than 29 characters for compatibility. Most modern cluster
+software should accept more.
+
+You will now be prompted to start entering your text.
+
+You finish the message by entering '/EX' on a new line. For instance:
+
+ ...
+ bye then Jim
+ 73 Dirk
+ /ex
+
+If you have started a message and you don't want to keep it then you
+can abandon the message with '/ABORT' on a new line, like:-
+
+ line 1
+ line 2
+ oh I just can't be bothered with this
+ /abort
+
+If you abort the message it will NOT be sent.
+
+When you are entering the text of your message, most normal output (such
+as DX announcements and so on are suppressed and stored for latter display
+(upto 20 such lines are stored, as new ones come along, so the oldest
+lines are dropped).
+
+Also, you can enter normal commands commands (and get the output
+immediately) whilst in the middle of a message. You do this by typing
+the command preceeded by a '/' character on a new line, so:-
+
+ /dx g1tlh 144010 strong signal
+
+Will issue a dx annoucement to the rest of the cluster.
+
+Also, you can add the output of a command to your message by preceeding
+the command with '//', thus :-
+
+ //sh/vhftable
+
+This will show YOU the output from SH/VHFTABLE and also store it in the
+message.
+
+You can carry on with the message until you are ready to send it.
=== 0^SET/ADDRESS <your address>^Record your postal address
=== 0^SET/ANNOUNCE^Allow announce messages to come out on your terminal
/EX
+If you are in 'Talk' mode, there is an extention to the '/' command which
+allows you to send the output to all the people you are talking to. You do
+with the '//' command. For example:-
+
+ //sh/hftable
+
+will send the hftable as you have it to all the people you are currently
+talking to.
+
=== 0^TYPE <filearea>/<name>^Look at the contents of a file in one of the fileareas
Type out the contents of a file in a filearea. So, for example, in
filearea 'bulletins' you want to look at file 'arld051' you would